1. <ol id="4zecw"><object id="4zecw"><blockquote id="4zecw"></blockquote></object></ol>

        <button id="4zecw"></button>
      1. <tbody id="4zecw"></tbody>

            <th id="4zecw"></th>
                  <dd id="4zecw"></dd>
                1. <dd id="4zecw"><center id="4zecw"></center></dd>

                2. <th id="4zecw"></th>
                3. <button id="4zecw"></button>

                  <tbody id="4zecw"><pre id="4zecw"></pre></tbody>

                  <th id="4zecw"></th>
                  欢迎访问济南朗坤暖通工程有限公司网站!!!

                  三个重要的安装决定了地暖的效果!

                  来源:http://www.takhleek.com/ 发布时间:2022/01/13

                  1、安装隔热层。在安装之前要检查地面是不是平整,是不是整洁。首先要先准备好电源线和探头,然后逐张铺设保温板,铺设后要查看一下铺设的是不是平整。
                  1. Install insulation. Before installation, check whether the ground is flat and tidy. First, prepare the power cord and probe, and then lay the insulation board one by one. After laying, check whether the laying is flat.
                  在边角处需要安装边角保温,保温板的切割应该平整,以免在铺设的时候会存在一些缝隙,间隙不得大于5毫米,保温板之间需要用宽胶带粘平整,确定保温板的表面是平整的,保证没有翘起的地方。
                  The corner insulation shall be installed at the corner. The cutting of the insulation board shall be flat to avoid some gaps during laying. The gap shall not be greater than 5mm. The insulation board shall be glued and leveled with wide adhesive tape. Finally, it shall be determined that the surface of the insulation board is flat to ensure that there is no warped place.
                  2、安装发射层。在已经铺好的隔热层上面平铺反射薄膜,反射膜之间可以留一些空隙,铺开。 安装发热层:首先是画线,根据图纸的设计,在保温板上画出电热膜需要铺设的位置线;然后是剔槽,在保温层上剔出导线的管槽;接着铺设相应规格的地热膜,地热膜在铺设的时候一定要正面朝上。
                  2. Install the emitter layer. The reflective film is laid on the paved thermal insulation layer, and some gaps can be left between the reflective films. Installation of heating layer: first, draw lines. According to the design of the drawing, draw the position line of the electric heating film to be laid on the insulation board; Then, the groove shall be removed, and the pipe groove of the conductor shall be removed on the insulation layer; Then lay the geothermal membrane of corresponding specifications, and the geothermal membrane must face up when laying.
                  济南地暖
                  还有每条电热膜之间要保持一定的距离,用胶带固定好,另外膜接线侧需距墙面200mm左右距离,将电热膜铺好后,在未接线侧两端铜片载流条先用进口胶泥粘好,再用防水绝缘胶带粘在胶泥上做好绝缘,还需要接线,穿管以及测试等步骤。
                  In addition, a certain distance shall be maintained between each electric heating film and fixed with adhesive tape. In addition, the wiring side of the film shall be about 200mm away from the wall. After the electric heating film is paved, the copper current carrying strips at both ends of the non wiring side shall be glued with imported adhesive plaster, and then the waterproof insulating tape shall be glued on the adhesive plaster for insulation. Wiring, threading and testing are also required.
                  3、安装温控器。需要按照设计的要求选择合适的温控器,在安装温控器的时候需要将供电系统关闭。
                  3. Install the thermostat. The appropriate temperature controller shall be selected according to the design requirements, and the power supply system shall be shut down when installing the temperature controller.
                  电地暖的安装价格主要与三个方面有关:发热材料、每平米铺设功率和温控器,其他的相关辅材价格都差不多。电地暖的发热电缆分为碳纤维发热电缆和单、双导发热电缆,这三种发热电缆的报价依次为:碳纤维>双导>单导。此外,发热电缆的价格还与功率有关,如果发热电缆的价格相同。
                  The installation price of electric floor heating is mainly related to three aspects: heating materials, laying power per square meter and temperature controller, and the prices of other relevant auxiliary materials are similar. Heating cables for electric floor heating are divided into carbon fiber heating cables and single and double conductor heating cables. The quotation of these three heating cables is as follows: carbon fiber > double conductor > single conductor. In addition, the price of heating cable is also related to power, if the price of heating cable is the same.
                  男人av无码天堂_野外性xxxxfreexxxx_日韩精品亚洲国产一区蜜芽_色偷偷av老熟女